RANCANG BANGUN INSTRUMENTASI MESIN UJI TARIK KAPASITAS 5 TON

Authors

  • Rifky rosid apriandik Universitas nusantara PGRI kediri Indonesia
  • Ali Akbar Universitas Nusantara PGRI Kediri Indonesia

DOI:

https://doi.org/10.29407/f6213902

Abstract

Penelitian ini mengulas tentang desain dan implementasi sistem instrumentasi pada mesin uji tarikdengan kapasitas 5 ton. Tahapan yang dilakukanmencakup perancangan sensor pengukur gaya dan perubahan panjang, pembuatan sistem pengendali, hinggaproses pemasangan dan pengkalibrasian. Uji cobadilakukan dengan menggunakan baja karbon sebagaisampel untuk menilai performa sistem. Berdasarkan hasilpengujian, sistem ini mampu mencatat data gaya sertaregangan dengan tingkat akurasi yang tinggi, sertamenghasilkan kurva tegangan-regangan yang sahih. Dengan demikian, sistem ini layak digunakan dalampengujian material baik untuk keperluan riset maupunaplikasi industri.

Keywords:

UJI TARIK, TEGANGAN , REGANGAN

##plugins.themes.default.displayStats.downloads##

##plugins.themes.default.displayStats.noStats##

References

[1]​M. M. Mallomoang, “Rancang Bangun Alat Uji Tarik Serat Berbasis Digital,” Mach. J. Tek. Mesin, vol. 8, no. 1, pp. 39–44, 2022, doi: 10.33019/jm.v8i1.2807.

[2]​R. R. Al Wafi, Rancang Bangun Alat Uji Tarik Dengna Kapasitas Maksimal 1 Ton. 2018. doi: https://repository.unej.ac.id/handle/123456789/88391.

[3]​D. Prabowo, U. S. Jati, and U. P. Hardini, “Simulasi Tegangan ( Stress ) Pada Komponen Rangka Mesin Uji Tarik Sealent Menggunakan Solidworks,” vol. 14, no. 02, pp. 405–412, 2023, doi: 10.35970/infotekmesin.v14i2.1947.

[4]​P. Pandiatmi, I. Okariawan, E. D. Sulistyowati, S. Salman, and I. A. K. C. Adhi, “Pembuatan mesin uji tarik kapasitas kecil: bagian data akuisisi,” Din. Tek. Mesin, vol. 7, no. 1, pp. 45–49, 2017, doi: 10.29303/d.v7i1.6.

[5]​D. L. Zariatin, R. M. Kurniawan, and N. Ikhsan, “Pengembangan alat uji tarik dengan beban maksimal 2 kN,” Din. Tek. Mesin, vol. 11, no. 2, p. 96, 2021, doi: 10.29303/dtm.v11i2.371.

[6]​G. Feberius, “Pembuatan Alat Uji Tarik Universal Statis Degan Penggrak Servomotor Berkapasitas Maksimum 1Kn,” 2018, doi: https://repositori.uma.ac.id/handle/123456789/16974.

[7]​R. Yulianto and Yandri, “Pembuatan Modifikasi Alat Uji Tarik di Laboratorium Universitas Batam,” vol. 9, no. 1, pp. 24–32, 2018, doi: https://doi.org/10.37776/zm.v9i1.151.

[8]​Gerson, S. Tri Kismanti, and M. Firdan Nurdin, “Rancang Bangun Mesin Uji Tarik, Tekan, dan Tekuk (Bending) Menggunakan Tenaga Hidrolik,” Artikel, vol. 2, pp. 1–14, 2023, doi: https://doi.org/10.35334/bearings.v2i1.3291.

[9]​P. MALAU, “PERANCANGAN ALAT UJI TARIK UNIVERSAL STATIS DENGAN PENGGERAK SERVOMOTOR BERKAPASITAS MAKSIMUM 1 kN,” vol. 44, no. 2, pp. 8–10, 2022, doi: https://repositori.uma.ac.id/handle/123456789/16976.

[10]​H. Budiman, “Analisis Pengujian Tarik (Tensile Test) Pada Baja St37 Dengan Alat Bantu Ukur Load Cell,” J-Ensitec, vol. 3, no. 01, pp. 9–13, 2016, doi: 10.31949/j-ensitec.v3i01.309.

Prosiding SEMNAS INOTEK (Seminar Nasional Inovasi Teknologi) 2025​3

Downloads

Published

2025-07-10

Issue

Vol. 9 No. 2 (2025): Prosiding Seminar Nasional Inovasi Teknologi Tahun 2025

Section

Articles

License

Copyright (c) 2025 Rifky rosid apriandik, Ali Akbar

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Authors who publish with this journal agree to the following terms:

  1. Copyright on any article is retained by the author(s).
  2. The author grants the journal, right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work’s authorship and initial publication in this journal.
  3. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal’s published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  4. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
  5. The article and any associated published material is distributed under the Creative Commons Attribution-ShareAlike 4.0 International License

How to Cite

RANCANG BANGUN INSTRUMENTASI MESIN UJI TARIK KAPASITAS 5 TON. (2025). Prosiding SEMNAS INOTEK (Seminar Nasional Inovasi Teknologi), 9(2), 991-996. https://doi.org/10.29407/f6213902