Variasi Pembebanan Rangka Mesin Pengaduk Bumbu Tabur Menggunkan Simulasi Autodesk Inventor
DOI:
https://doi.org/10.29407/inotek.v8i2.4967Abstract
Tujuan penelitian ini untuk mengetahui beban variasi gaya pembebanan 200N, 300N, dan 400N terhadap kekuatan rangka mesin pengaduk bumbu tabur dirancang dengan material stainless steel 440C tipe hollow ukuran 33 2. Metode penelitian meliputi menentukan variasi pembebanan, pemodelan desain 3D menggunakan software inventor, penginputan beban variasi, run simulasi, dan analisa hasil simulasi, dan evaluasi hasil simulasi. Hasil simulasi pembebanan 200 N Von Mises Strees nilai maxsimal 2,527 Mpa dan minimum 0 MPa, Displecement memcapai nilai maksimal 0,003583 mm dan minimum 0 mm , Safety Factot memperoleh mendapat 15 ul. Hasil simulasi pembebanan 300 N nilai von mises strees maksimal 3,791 Mpa dan minimum 0 MPa , nilai displecement maksimal 0,005375 mm dan minimum 0 mm, Safety Factor 15ul. Hasil simulasi pembebanan 400 N nilai maksimal Von Mises Strees 5,054 Mpa dan minimum 0 MPa , Displecemen nilai maksimal 0,007166 mm dan minimum 0 mm, Safety Factor 15ul.
Keywords:
Inventor, simulasi, rangka##plugins.themes.default.displayStats.downloads##
References
D. Bengle et al., “Pendampingan Pengolahan Keripik Jamur di UKM Jamur,” vol. 6, no. 2, pp. 610–615, 2023.
M. Taufiq and R. S. Wijaya, “MELALUI TEKNOLOGI TEPAT GUNA SPINNER Pendahuluan Metode,” vol. 1, no. 3, pp. 205–210, 2023.
Z. F. Emzain, N. Qosim, and L. Agustriyana, “MENINGKATKAN EFISIENSI PROSES PRODUKSI UMKM,” vol. 7, no. 5, pp. 1–10, 2023.
J. T. Mesin, F. Teknik, and U. Surabaya, “PERANCANGAN DESAIN MESIN PEMOTONG SINGKONG DAN SIMULASI METODE ELEMEN HINGGA ( STUDI KASUS : UKM ZEANS SNACK ) Dihral Maibi Dyah Riandadari,” no. 84.
H. Kuncoro and A. Yudha, “ANALISIS RANGKA MESIN PEMISAH KUNING TELUR MENGGUNAKAN SOFTWARE SOLIDWORKS 2020,” vol. 25, no. 1, 2023.
J. T. Mesin, “Desain dan Analisis Kekuatan Rangka Mesin Pres Batako Menggunakan Finite Element Method,” vol. 5, pp. 221–230, 2023.
D. Prabowo, U. S. Jati, and U. P. Hardini, “Simulasi Tegangan ( Stress ) Pada Komponen Rangka Mesin Uji Tarik Sealent Menggunakan Solidworks,” vol. 14, no. 02, pp. 405–412, 2023, doi: 10.35970/infotekmesin.v14i2.1947.
M. M. Fea, “Analisis statik bracket roll brush mesin tensor menggunakan metode fea 1,2),” vol. 10, no. 1, pp. 57–63, 2023.
I. G. Kristanto, N. Mulyaningsih, and F. Hilmy, “SIMULASI STRUKTUR RANGKA MESIN PENCACAH SABUT KELAPA,” 2023.
Z. N. Alif, “ANALYSIS KEKUATAN STANDAR SAMPING MOTOR MENGGUNAKAN STEEL CARBON DENGAN BEBAN 1500 N MENGGUNAKAN METODE FINITE ELEMEN ANALYSIS,” vol. 9, no. 2, pp. 102–107, 2023.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Khoirul Widodo, Nuryosuwito
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Copyright on any article is retained by the author(s).
- The author grants the journal, right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work’s authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal’s published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
- The article and any associated published material is distributed under the Creative Commons Attribution-ShareAlike 4.0 International License
